Hirdetés

Új hozzászólás Aktív témák

  • lanszelot

    addikt

    Hello,

    Ez a videó alapján a bkink -et próbalom Attiny85 -re feltölteni, de hiba kódot dob.

    Ez a hibakód:
    "Arduino: 1.8.18 (Windows 10), Board: "ATtiny25/45/85, ATtiny85, Internal 1 MHz"

    Sketch uses 676 bytes (8%) of program storage space. Maximum is 8192 bytes.

    Global variables use 9 bytes (1%) of dynamic memory, leaving 503 bytes for local variables. Maximum is 512 bytes.

    C:\Users\robag\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/bin/avrdude -CC:\Users\robag\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf -v -pattiny85 -cstk500v1 -PCOM3 -b19200 -Uflash:w:C:\Users\robag\AppData\Local\Temp\arduino_build_247506/Blink.ino.hex:i

    avrdude: Version 6.3-20190619
    Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
    Copyright (c) 2007-2014 Joerg Wunsch

    System wide configuration file is "C:\Users\robag\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf"

    Using Port : COM3
    Using Programmer : stk500v1
    Overriding Baud Rate : 19200
    AVR Part : ATtiny85
    Chip Erase delay : 400000 us
    PAGEL : P00
    BS2 : P00
    RESET disposition : possible i/o
    RETRY pulse : SCK
    serial program mode : yes
    parallel program mode : yes
    Timeout : 200
    StabDelay : 100
    CmdexeDelay : 25
    SyncLoops : 32
    ByteDelay : 0
    PollIndex : 3
    PollValue : 0x53
    Memory Detail :

    Block Poll Page Polled

    Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

    ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------

    eeprom 65 12 4 0 no 512 4 0 4000 4500 0xff 0xff
    flash 65 6 32 0 yes 8192 64 128 30000 30000 0xff 0xff
    signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
    lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
    lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
    hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
    efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
    calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00

    Programmer Type : STK500
    Description : Atmel STK500 Version 1.x firmware
    Hardware Version: 3
    Firmware Version: 6.2
    Vtarget : 0.3 V
    Varef : 0.3 V
    Oscillator : 28.800 kHz
    SCK period : 3.3 us

    avrdude: AVR device initialized and ready to accept instructions

    Reading | ################################################## | 100% 0.02s

    avrdude: Device signature = 0x000000 (retrying)

    Reading | ################################################## | 100% 0.02s

    avrdude: Device signature = 0x000000 (retrying)

    An error occurred while uploading the sketch

    Reading | ################################################## | 100% 0.02s

    avrdude: Device signature = 0x000000

    avrdude: Yikes! Invalid device signature.
    Double check connections and try again, or use -F to override
    this check.

    avrdude done. Thank you.

    This report would have more information with
    "Show verbose output during compilation"
    option enabled in File -> Preferences.
    "

    Miért dob hiba kódot?

    Sikerült volna kukáznom az Attiny85-t? Azt hogy tudom ellenőrizni, hogy működik e még?

Új hozzászólás Aktív témák