Hirdetés

  2. Fórumok
  3. LOGOUT reakciók
  4. Új firmware D-Link ADSL modemekhez
Keresés

Hirdetés

CyberSecurity Connect - blended learning, valódi labor kísérletezésre. Kiberbiztonsági képzés profiktól!
(használd a CYBSEC25PH kuponkódot további 20 ezer ft kedvezményért!)

Új hozzászólás Aktív témák

  • #190 promark csendes tag dchard #136
    Új Válasz #190
    Új hozzászólás
    Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra
    Privát üzenet küldése

    promark

    csendes tag

    válasz dchard #136 üzenetére

    DSL 321B
    Gyárilag: H/W Ver.: D1 , F/W Ver.: EU_1.00
    Frissítve először F/W.: DE_1.01, másodszor DE_1.03
    Ami érdekesség, hogy a második frissítés (DE_1.03) átállította a H/W-t D2-re.

    # dmesg
    Linux version 2.6.8.1 (root@mochow) (gcc version 3.4.2) #1 Tue Dec 28 20:12:52 CST 2010
    Serial flash device: name S25FL016A, id 0x0114, size 2048KB
    96332CG prom init
    CPU revision is: 00029010
    Determined physical RAM map:
    memory: 007a0000 @ 00000000 (usable)
    On node 0 totalpages: 1952
    DMA zone: 1952 pages, LIFO batch:1
    Normal zone: 0 pages, LIFO batch:1
    HighMem zone: 0 pages, LIFO batch:1
    Built 1 zonelists
    Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
    brcm mips: enabling icache and dcache...
    Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
    Primary data cache 8kB 2-way, linesize 16 bytes.
    PID hash table entries: 32 (order 5: 256 bytes)
    Using 120.000 MHz high precision timer.
    Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
    Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Memory: 6048k/7808k available (1260k kernel code, 1740k reserved, 187k data, 64k init, 0k highmem)
    Calibrating delay loop... 239.20 BogoMIPS
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    Checking for 'wait' instruction... unavailable.
    NET: Registered protocol family 16
    Total Flash size: 2048K with 32 sectors
    File system address: 0xbfc10100
    Can't analyze prologue code at 80149d04
    PPP generic driver version 2.4.2
    NET: Registered protocol family 24
    Using noop io scheduler
    bcm963xx_mtd driver v1.0
    brcmboard: brcm_board_init entry

    ======= GPIO CONFIG_BCM96338 inited ========
    Serial: BCM63XX driver $Revision: 3.00 $
    ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
    NET: Registered protocol family 2
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 512 bind 1024)
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Ebtables v2.0 registered
    NET: Registered protocol family 8
    NET: Registered protocol family 20
    VFS: Mounted root (squashfs filesystem) readonly.
    Freeing unused kernel memory: 64k freed
    Algorithmics/MIPS FPU Emulator v1.5
    atmapi: module license 'Proprietary' taints kernel.
    adsl: adsl_init entry
    blaadd: blaa_detect entry
    Broadcom BCMPROCFS v1.0 initialized
    Broadcom BCM6338A2 Ethernet Network Device v0.3 Dec 28 2010 20:12:06
    Config Internal PHY Through MDIO
    BCM63xx_ENET: 100 MB Full-Duplex (auto-neg)
    eth0: MAC Address: 00:26:5A:01:F3:61
    eth0 Link UP.
    ZIPB............
    FLAG: 1
    BcmAdsl_Initialize=0xC00683F8, g_pFnNotifyCallback=0xC00810A4
    AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003980 adsl2=0x00000000
    pSdramPHY=0xA07FFFF8, 0x0 0x0
    AdslCoreHwReset: AdslOemDataAddr = 0xA07F9244
    AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00003980 adsl2=0x00000000
    DoInitialize: do kerSysRegisterDyingGaspHandler
    dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
    DoInitialize: do put_user
    DoInitialize: do kerSysLedCtrl
    ATM proc init !!!
    ZIPB............
    FLAG: 1
    ADSL G.994 training
    Device UP br0
    Fib_add_ifaddr : DEV br0
    Device UP: br0
    Device add to fib: br0
    device eth0 entered promiscuous mode
    br0: port 1(eth0) entering learning state
    br0: topology change detected, propagating
    br0: port 1(eth0) entering forwarding state
    device nas_0_1_32 entered promiscuous mode
    br0: port 2(nas_0_1_32) entering learning state
    br0: topology change detected, propagating
    br0: port 2(nas_0_1_32) entering forwarding state
    eth0 Link DOWN.
    eth0 Link UP.

    ioctl, p_name=diapd
    ADSL G.992 started

  • #178 xabolcs őstag dchard #136
    Új Válasz #178
    Új hozzászólás
    Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra
    Privát üzenet küldése

    xabolcs

    őstag

    válasz dchard #136 üzenetére

    szia,

    most vettem egy modemet:

    DSL-321B
    - H/W Ver: D2
    - F/W Ver: EU_1.01
    - made in china :P

    s kovetkezot valaszolta:

    #
    # dmesg
    Linux version 2.6.8.1 (root@BB3) (gcc version 3.4.2) #1 Thu Oct 22 09:42:16 CST 2009
    Serial flash device: name W25X16VSSIG, id 0xef14, size 2048KB
    96332CG prom init
    CPU revision is: 00029010
    Determined physical RAM map:
    memory: 007a0000 @ 00000000 (usable)
    On node 0 totalpages: 1952
    DMA zone: 1952 pages, LIFO batch:1
    Normal zone: 0 pages, LIFO batch:1
    HighMem zone: 0 pages, LIFO batch:1
    Built 1 zonelists
    Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
    brcm mips: enabling icache and dcache...
    Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
    Primary data cache 8kB 2-way, linesize 16 bytes.
    PID hash table entries: 32 (order 5: 256 bytes)
    Using 120.000 MHz high precision timer.
    Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
    Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Memory: 6048k/7808k available (1261k kernel code, 1740k reserved, 187k data, 64k init, 0k highmem)
    Calibrating delay loop... 239.20 BogoMIPS
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    Checking for 'wait' instruction... unavailable.
    NET: Registered protocol family 16
    Total Flash size: 2048K with 512 sectors
    File system address: 0xbfc10100
    Can't analyze prologue code at 80149dd4
    PPP generic driver version 2.4.2
    NET: Registered protocol family 24
    Using noop io scheduler
    bcm963xx_mtd driver v1.0
    brcmboard: brcm_board_init entry

    ======= GPIO CONFIG_BCM96338 inited ========
    Serial: BCM63XX driver $Revision: 3.00 $
    ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
    NET: Registered protocol family 2
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 512 bind 1024)
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Ebtables v2.0 registered
    NET: Registered protocol family 8
    NET: Registered protocol family 20
    VFS: Mounted root (squashfs filesystem) readonly.
    Freeing unused kernel memory: 64k freed
    Algorithmics/MIPS FPU Emulator v1.5
    atmapi: module license 'Proprietary' taints kernel.
    adsl: adsl_init entry
    blaadd: blaa_detect entry
    Broadcom BCMPROCFS v1.0 initialized
    Broadcom BCM6338A2 Ethernet Network Device v0.3 Oct 22 2009 09:41:13
    Config Internal PHY Through MDIO
    BCM63xx_ENET: Auto-negotiation timed-out
    BCM63xx_ENET: 10 MB Half-Duplex (assumed)
    eth0: MAC Address: F0:7D:68:6D:98:31
    BcmAdsl_Initialize=0xC00683C8, g_pFnNotifyCallback=0xC0081004
    AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
    pSdramPHY=0xA07FFFF8, 0x402004 0x88000010
    AdslCoreHwReset: AdslOemDataAddr = 0xA07F9244
    AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
    dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
    ATM proc init !!!
    ip_tables: (C) 2000-2002 Netfilter core team
    ipt_time loading
    ip_queue: Unknown symbol dynahelper_unrefct
    ip_queue: Unknown symbol dynahelper_unrefnat
    ip_queue: Unknown symbol dynahelper_refnat
    ip_queue: Unknown symbol dynahelper_tracknat
    ip_queue: Unknown symbol dynahelper_trackct
    ip_queue: Unknown symbol dynahelper_untracknat
    ip_queue: Unknown symbol dynahelper_untrackct
    ip_queue: Unknown symbol dynahelper_refct
    ZIPB............
    FLAG: 1
    Device UP br0
    Fib_add_ifaddr : DEV br0
    Device UP: br0
    Device add to fib: br0
    device eth0 entered promiscuous mode
    br0: port 1(eth0) entering learning state
    br0: topology change detected, propagating
    br0: port 1(eth0) entering forwarding state
    device nas_0_1_32 entered promiscuous mode
    br0: port 2(nas_0_1_32) entering learning state
    br0: topology change detected, propagating
    br0: port 2(nas_0_1_32) entering forwarding state

    ioctl, p_name=diapd
    br0: port 1(eth0) entering disabled state
    AdslCoreEcUpdTmr: timeMs=1800530 ecUpdMask=0x40000
    eth0 Link UP.
    br0: port 1(eth0) entering learning state
    br0: topology change detected, propagating
    br0: port 1(eth0) entering forwarding state
    eth0 Link DOWN.
    br0: port 1(eth0) entering disabled state
    eth0 Link UP.
    br0: port 1(eth0) entering learning state
    br0: topology change detected, propagating
    br0: port 1(eth0) entering forwarding state
    #

Új hozzászólás Aktív témák