- Milyen okostelefont vegyek?
- iPhone topik
- Motorola Edge 50 Neo - az egyensúly gyengesége
- Samsung Galaxy S24 Ultra - ha működik, ne változtass!
- Okosóra és okoskiegészítő topik
- Apple iPhone 16 Pro - rutinvizsga
- Azonnali mobilos kérdések órája
- Magisk
- Samsung Galaxy S21 és S21+ - húszra akartak lapot húzni
- Xiaomi 15 - kicsi telefon nagy energiával
-
Mobilarena
Amit érdemes tudni a Raspberry Pi-kről:
A legelső változat 2012-ben jelent meg. Pici, olcsó és nagyon alacsony fogyasztású, hobby-célú kártyagép. Felépítése ARM alapú, nem PC-architektúra, hanem kb. egy régi mobilhoz hasonló. Nagyon sok mindenre használható! A Linux-nak és a magas eladási mennyiségnek köszönhetően jelentős fejlesztőtáborral rendelkezik.
Új hozzászólás Aktív témák
-
Plehboj
tag
válasz
JoceeHunt #40741 üzenetére
Nem működő reboot problémára (USB-és segédtáp/tápos hub használata esetén jön elő rpi4-en) találtam egy hozzászólást egy fórumon.
Tudna valaki - aki ért mélyebben az elektronikához - segíteni abban, hogy pontosan mit és hogyan kellene bütykölni ehhez ?Itt a leírás hozzá:
I tried first using a schottkey diode between the power to the hub and the hub but this didn't help. I decided to see what happened with the red removed altogether. This still didn't help either.
I can't recall all the details off the top of my head but part of how USB works involves the hub pulling up USB data lines at times and it seems this is either enough to allow a voltage to then leak back to the power rails the RPi PMIC is checking, or that the problem is in fact slightly different and somehow caused by the presence of a USB hub at boot confusing the bootloader. In either case the solution I came up with was a simple modification to the hub using a few bits out the parts bin and 10 minutes with the soldering iron. I found* an NPN transistor,
* a P channel MOSFET (grossly over-rated at 61 Amps, but that's what I had to hand) and
* a couple of 4k7 resistors.The VBus signal (red wire) from the host connects to the base of the transistor via a 4k7 resistor. The Emitter is connected to GND (black wire from host). The Source of the FET connects to the external power source in (which is isolated from the hub), and the Drain to the hubs power rail. The collector of the transistor is connected to the gate of the FET such that it is pulled down when the host provides power, thus switching on the FET and powering the hub. The remaining 4k7 resistor between the Power source and the gate prevents it floating around. Finally I put the Schottky diode back in place such that the hub can still be used without external power.
My rpi4 now boots perfectly every time (from LAN) and with a USB DVD drive connected, something the previous rpi3 wouldn't do.
-
UberMutant
őstag
válasz
JoceeHunt #40718 üzenetére
csinálsz egy SD kártyát raspbian OS sel.
#2 teszel rá egy SSH nevű, kiterjesztés nélküli filet.
ha wifi is kell egy wpa_supplicant.conf fileba tedd be:country=HU
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
network={
ssid="wifid SSIDje"
psk="wifi jelszó, az idézőjel is kell"
}bootolsz.
SSH-n belépsz PIra. pi/ raspberry párossal
utána a raspi-config gal végegesíted az SSH dropbear szervert.
Új hozzászólás Aktív témák
Hirdetés
- DUPLA XEON GOLD 6134!!! HP Z8 G4 LEGNAGYOBB WORKSTATION 64GB 2x8 mag 2x16 szál gamer, szerver, munka
- BESZÁMÍTÁS! ASROCK B650 R5 7600X 32GB DDR5 1TB SSD RTX 3070 8GB MSI MPG Gungnir 100 Enermax 750W
- Telefon felvásárlás!! iPhone 13 Mini/iPhone 13/iPhone 13 Pro/iPhone 13 Pro Max/
- Realme 8i 64GB / Normál állapotban / 12 hónap jótállással
- ÚJ Apple Macbook Air 15,3 M4 10C CPU/10C GPU/16GB/256GB - Ezüst -(2025)- 3 Ciklus-3 év gari - MAGYAR
Állásajánlatok
Cég: PC Trade Systems Kft.
Város: Szeged
Cég: CAMERA-PRO Hungary Kft
Város: Budapest