Új hozzászólás Aktív témák

• #1379 poli27 Topikgazda

  Új Válasz 2023-04-08 09:56:27 #1379

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  poli27

  Topikgazda

  Ha valakit érdekel gyári start Gcode P1P re, amibe az ágy szélénél a csíkhúzás után megtörli az fejet, csináltam eggyet Sokszor az volt a bajom, hogy belerondított a kezdésbe a bevitt maszat...

  ;===== machine: P1P ========================
  ;===== date: 202230129 =====================
  ;===== reset machine status =================
  M17 X1.2 Y1.2 Z0.75 ; reset motor current to default
  M960 S5 P1 ; turn on logo lamp
  G90
  M220 S100 ;Reset Feedrate
  M221 S100 ;Reset Flowrate
  M73.2 R1.0 ;Reset left time magnitude
  M1002 set_gcode_claim_speed_level : 5
  M221 X0 Y0 Z0 ; turn off soft endstop to prevent protential logic problem
  G29.1 Z{+0.0} ; clear z-trim value first

  ;===== heatbed preheat ====================
  M1002 gcode_claim_action : 2
  M140 S[bed_temperature_initial_layer_single] ;set bed temp
  M190 S[bed_temperature_initial_layer_single] ;wait for bed temp

  ;=============turn on fans to prevent PLA jamming=================
  {if filament_type[initial_tool]=="PLA"}
  {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}
  M106 P3 S180
  {elsif (bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}
  M106 P3 S255
  {endif};Prevent PLA from jamming
  {endif}
  M106 P2 S100 ; turn on big fan ,to cool down toolhead

  ;===== prepare print temperature and material ==========
  M104 S[nozzle_temperature_initial_layer] ;set extruder temp
  G91
  G0 Z10 F1200
  G90
  G28 X
  M975 S1 ; turn on
  G1 X60 F12000
  G1 Y245
  G1 Y265 F3000
  M620 M
  M620 S[initial_tool]A ; switch material if AMS exist
  M109 S[nozzle_temperature_initial_layer]
  G1 X120 F12000

  G1 X20 Y50 F12000
  G1 Y-3
  T[initial_tool]
  G1 X54 F12000
  G1 Y265
  M400
  M621 S[initial_tool]A

  M412 S1 ; ===turn on filament runout detection===

  M109 S250 ;set nozzle to common flush temp
  M106 P1 S0
  G92 E0
  G1 E50 F200
  M400
  M104 S[nozzle_temperature_initial_layer]
  G92 E0
  G1 E50 F200
  M400
  M106 P1 S255
  G92 E0
  G1 E5 F300
  M109 S{nozzle_temperature_initial_layer[initial_extruder]-20} ; drop nozzle temp, make filament shink a bit
  G92 E0
  G1 E-0.5 F300

  G1 X70 F9000
  G1 X76 F15000
  G1 X65 F15000
  G1 X76 F15000
  G1 X65 F15000; shake to put down garbage
  G1 X80 F6000
  G1 X95 F15000
  G1 X80 F15000
  G1 X165 F15000; wipe and shake
  M400
  M106 P1 S0
  ;===== prepare print temperature and material end =====

  ;===== wipe nozzle ===============================
  M1002 gcode_claim_action : 14
  M975 S1
  M106 S255
  G1 X65 Y230 F18000
  G1 Y264 F6000
  M109 S{nozzle_temperature_initial_layer[initial_extruder]-20}
  G1 X100 F18000 ; first wipe mouth

  G0 X135 Y253 F20000 ; move to exposed steel surface edge
  G28 Z P0 T300; home z with low precision,permit 300deg temperature
  G29.2 S0 ; turn off ABL
  G0 Z5 F20000

  G1 X60 Y265
  G92 E0
  G1 E-0.5 F300 ; retrack more
  G1 X100 F5000; second wipe mouth
  G1 X70 F15000
  G1 X100 F5000
  G1 X70 F15000
  G1 X100 F5000
  G1 X70 F15000
  G1 X100 F5000
  G1 X70 F15000
  G1 X90 F5000
  G0 X128 Y261 Z-1.5 F20000 ; move to exposed steel surface and stop the nozzle
  M104 S140 ; set temp down to heatbed acceptable
  M106 S255 ; turn on fan (G28 has turn off fan)

  M221 S; push soft endstop status
  M221 Z0 ;turn off Z axis endstop
  G0 Z0.5 F20000
  G0 X125 Y259.5 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y262.5
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y260.0
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y262.0
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y260.5
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y261.5
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 Z0.5 F20000
  G0 X125 Y261.0
  G0 Z-1.01
  G0 X131 F211
  G0 X124
  G0 X128
  G2 I0.5 J0 F300
  G2 I0.5 J0 F300
  G2 I0.5 J0 F300
  G2 I0.5 J0 F300

  M109 S140 ; wait nozzle temp down to heatbed acceptable
  G2 I0.5 J0 F3000
  G2 I0.5 J0 F3000
  G2 I0.5 J0 F3000
  G2 I0.5 J0 F3000

  M221 R; pop softend status
  G1 Z10 F1200
  M400
  G1 Z10
  G1 F30000
  G1 X230 Y15
  G29.2 S1 ; turn on ABL
  ;G28 ; home again after hard wipe mouth
  M106 S0 ; turn off fan , too noisy
  ;===== wipe nozzle end ================================

  ;===== bed leveling ==================================
  M1002 judge_flag g29_before_print_flag
  M622 J1

  M1002 gcode_claim_action : 1
  G29 A X{first_layer_print_min[0]} Y{first_layer_print_min[1]} I{first_layer_print_size[0]} J{first_layer_print_size[1]}
  M400
  M500 ; save cali data

  M623
  ;===== bed leveling end ================================

  ;===== home after wipe mouth============================
  M1002 judge_flag g29_before_print_flag
  M622 J0

  M1002 gcode_claim_action : 13
  G28

  M623
  ;===== home after wipe mouth end =======================

  M975 S1 ; turn on vibration supression

  ;=============turn on fans to prevent PLA jamming=================
  {if filament_type[initial_tool]=="PLA"}
  {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}
  M106 P3 S180
  {elsif (bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}
  M106 P3 S255
  {endif};Prevent PLA from jamming
  {endif}
  M106 P2 S100 ; turn on big fan ,to cool down toolhead

  M104 S{nozzle_temperature_initial_layer[initial_extruder]} ; set extrude temp earlier, to reduce wait time

  ;===== mech mode fast check============================
  G1 X128 Y128 Z10 F20000
  M400 P200
  M970.3 Q1 A7 B30 C80 H15 K0
  M974 Q1 S2 P0

  G1 X128 Y128 Z10 F20000
  M400 P200
  M970.3 Q0 A7 B30 C90 Q0 H15 K0
  M974 Q0 S2 P0

  M975 S1
  G1 F30000
  G1 X230 Y15
  G28 X ; re-home XY
  ;===== fmech mode fast check============================

  ;===== noozle load line ===============================
  M975 S1
  G90
  M83
  T1000
  G1 X18.0 Y1.0 Z0.8 F18000;Move to start position
  M109 S{nozzle_temperature_initial_layer[initial_extruder]}
  G1 Z0.2
  G0 E2 F300
  G0 X240 E15 F{outer_wall_volumetric_speed/(0.3*0.5) * 60}
  G0 Y11 E0.700 F{outer_wall_volumetric_speed/(0.3*0.5)/ 4 * 60}
  G0 X239.5
  G0 E0.2
  G0 Y1.5 E0.700
  G0 X18 E15 F{outer_wall_volumetric_speed/(0.3*0.5) * 60}
  M400

  ;===== Quick wipe sequence ===============
  G0 Y4 Z1.0 F6000 ;1mm lift and move 2mm on Y
  G0 Z0.0 ;press nozzle onto bed
  G0 Y8 F3000 ;start of 4 wipes movement
  G0 Y4 F3000
  G0 Y8 F3000
  G0 Y4 F3000
  G0 Y8 F3000
  G0 Y4 F3000
  G0 Y8 F3000 ;end of 4 wipes movement
  G0 Z0.4 ;raise nozzle up to prevent scratching bed

  ;===== for Textured PEI Plate , lower the nozzle as the nozzle was touching topmost of the texture when homing ==
  ;curr_bed_type={curr_bed_type}
  {if curr_bed_type=="Textured PEI Plate"}
  G29.1 Z{-0.04} ; for Textured PEI Plate
  {endif}
  ;========turn off light and wait extrude temperature =============
  M1002 gcode_claim_action : 0
  M106 S0 ; turn off fan
  M106 P2 S0 ; turn off big fan
  M106 P3 S0 ; turn off chamber fan

  M975 S1 ; turn on mech mode supression

  [ Szerkesztve ]

Új hozzászólás Aktív témák