Új hozzászólás Aktív témák

• #2003 csori23 aktív tag sztanozs #2002

  Új Válasz 2015-10-27 16:21:19 #2003

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  csori23

  aktív tag

  válasz sztanozs #2002 üzenetére

  1.28-as verzio van fenn. Most látom hogy már van frissebb, de azért ez sem nevezhető réginek.
  Lefuttatam, majd egymás alá illesztettem amiket irtál abban a sorrendben is. Kötöjelsorozattal vannak elválasztva.
  Take all parameters from the command line
  
  
  * usb_modeswitch: handle USB devices with multiple modes
  * Version 2.2.0 (C) Josua Dietze 2014
  * Based on libusb1/libusbx
  
  ! PLEASE REPORT NEW CONFIGURATIONS !
  
  DefaultVendor= 0x12d1
  DefaultProduct= 0x1505
  TargetVendor= 0x12d1
  TargetProduct= 0x1506
  MessageContent="55534243123456780000000000000011062000000100000000000000000000"
  NeedResponse=1
  
  Look for target devices ...
  found USB ID 1d6b:0003
  found USB ID 1d6b:0002
  found USB ID 12d1:1506
  vendor ID matched
  product ID matched
  Found devices in target mode or class (1)
  Look for default devices ...
  found USB ID 1d6b:0003
  found USB ID 1d6b:0002
  found USB ID 12d1:1506
  vendor ID matched
  No devices in default mode found. Nothing to do. Bye!
  ---------------------------------------------------------
  align=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  Hierarchical RCU implementation.
  RCU-based detection of stalled CPUs is disabled.
  Verbose stalled-CPUs detection is disabled.
  NR_IRQS:256
  MPCORE GIC init
  External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
  MPCORE Global Timer Clock 400000000Hz
  Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
  pid_max: default: 32768 minimum: 301
  Mount-cache hash table entries: 512
  CPU: Testing write buffer coherency: ok
  MPCORE Private timer setup CPU0
  Calibrating local timer... 399.856MHz.
  L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
  CPU1: Booted secondary processor
  MPCORE Private timer setup CPU1
  Brought up 2 CPUs
  SMP: Total of 2 processors activated (3198.15 BogoMIPS).
  devtmpfs: initialized
  atomic64 test passed
  NET: Registered protocol family 16
  Found a AMD NAND flash:
  Total size: 128MB
  Block size: 128KB
  Page Size: 2048B
  OOB Size: 64B
  Sector size: 512B
  Spare size: 16B
  ECC level: 8 (8-bit)
  Device ID: 0x 1 0xf1 0x 0 0x1d 0x 1 0xf1
  CCA UART Clock Config: Sel=1 Ovr=1 Div=48
  CCA UART Clock rate 100000000Hz
  bio: create slab <bio-0> at 0
  Switching to clocksource mpcore_gtimer
  NET: Registered protocol family 2
  IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
  TCP: Hash tables configured (established 8192 bind 8192)
  TCP reno registered
  UDP hash table entries: 128 (order: 0, 4096 bytes)
  UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
  NET: Registered protocol family 1
  PCI: CLS 0 bytes, default 32
  PCI: no core
  PCI: no core
  PCI: scanning bus 0
  pci 0000:00:00.0: reg 10: [mem 0x18000000-0x18000fff]
  pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:01.0: reg 10: [mem 0x18001000-0x18001fff]
  pci 0000:00:01.0: reg 14: [mem 0x18002000-0x18002fff]
  pci 0000:00:01.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:02.0: reg 10: [mem 0x1802c000-0x1802cfff]
  pci 0000:00:02.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:03.0: reg 10: [mem 0x18024000-0x18024fff]
  pci 0000:00:03.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:04.0: reg 10: [mem 0x18025000-0x18025fff]
  pci 0000:00:04.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:05.0: reg 10: [mem 0x18026000-0x18026fff]
  pci 0000:00:05.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:06.0: reg 10: [mem 0x18027000-0x18027fff]
  pci 0000:00:06.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:07.0: reg 10: [mem 0x18012000-0x18012fff]
  pci 0000:00:07.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:08.0: reg 10: [mem 0x18013000-0x18013fff]
  pci 0000:00:08.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:09.0: reg 10: [mem 0x18014000-0x18014fff]
  pci 0000:00:09.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0a.0: reg 10: [mem 0x1800b000-0x1800bfff]
  pci 0000:00:0a.0: reg 14: [mem 0x1800c000-0x1800cfff]
  pci 0000:00:0a.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0b.0: reg 10: [mem 0x18022000-0x18022fff]
  pci 0000:00:0b.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0b.1: reg 10: [mem 0x18021000-0x18021fff]
  pci 0000:00:0b.1: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0c.0: reg 10: [mem 0x18023000-0x18023fff]
  pci 0000:00:0c.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0d.0: reg 10: [mem 0x18020000-0x18020fff]
  pci 0000:00:0d.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0e.0: reg 10: [mem 0x18210000-0x1821ffff]
  pci 0000:00:0e.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:0f.0: reg 10: [mem 0x18010000-0x18010fff]
  pci 0000:00:0f.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:10.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:11.0: reg 10: [mem 0x18028000-0x18028fff]
  pci 0000:00:11.0: reg 30: [mem 0x00000000-0x000007ff pref]
  pci 0000:00:12.0: reg 10: [mem 0x18029000-0x18029fff]
  pci 0000:00:12.0: reg 30: [mem 0x00000000-0x000007ff pref]
  PCI: Fixing up bus 0
  PCIE1 link=1
  PCIE1 switching to GEN2
  PCIE1 link=1
  pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
  pci 0001:00:00.0: PME# disabled
  PCI: Fixing up bus 0
  PCI: bus0: Fast back to back transfers disabled
  pci 0001:01:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
  pci 0001:01:00.0: supports D1 D2
  PCI: Fixing up bus 1
  PCI: bus1: Fast back to back transfers disabled
  pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
  pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
  pci 0001:01:00.0: BAR 0: set to [mem 0x08000000-0x08007fff 64bit] (PCI address [0x8000000-0x8007fff]
  pci 0001:00:00.0: PCI bridge to [bus 01-01]
  pci 0001:00:00.0: bridge window [io disabled]
  pci 0001:00:00.0: bridge window [mem 0x08000000-0x080fffff]
  pci 0001:00:00.0: bridge window [mem pref disabled]
  PCIE2 link=1
  PCIE2 switching to GEN2
  PCIE2 link=1
  pci 0002:00:00.0: PME# supported from D0 D3hot D3cold
  pci 0002:00:00.0: PME# disabled
  PCI: Fixing up bus 0
  PCI: bus0: Fast back to back transfers disabled
  pci 0002:02:00.0: reg 10: [mem 0x40000000-0x40007fff 64bit]
  pci 0002:02:00.0: supports D1 D2
  PCI: Fixing up bus 2
  PCI: bus2: Fast back to back transfers disabled
  pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
  pci 0002:02:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
  pci 0002:02:00.0: BAR 0: set to [mem 0x40000000-0x40007fff 64bit] (PCI address [0x40000000-0x40007fff]
  pci 0002:00:00.0: PCI bridge to [bus 02-02]
  pci 0002:00:00.0: bridge window [io disabled]
  pci 0002:00:00.0: bridge window [mem 0x40000000-0x400fffff]
  pci 0002:00:00.0: bridge window [mem pref disabled]
  PCIE3 link=0
  VFS: Disk quotas dquot_6.5.2
  Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  squashfs: version 4.0 (2009/01/31) Phillip Lougher
  fuse init (API version 7.15)
  msgmni has been set to 498
  io scheduler noop registered (default)
  io scheduler deadline registered
  io scheduler cfq registered
  Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
  console [ttyS0] enabled, bootconsole disabled
  serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
  brd: module loaded
  loop: module loaded
  pflash: found no supported devices
  bcmsflash: found no supported devices
  Boot partition size = 524288(0x80000)
  lookup_nflash_rootfs_offset: offset = 0x200000
  nflash: squash filesystem with lzma found at block 29
  Creating 4 MTD partitions on "nflash":
  0x000000000000-0x000000080000 : "boot"
  0x000000080000-0x000000200000 : "nvram"
  0x000000200000-0x000002000000 : "linux"
  0x0000003ab988-0x000002000000 : "rootfs"
  PPP generic driver version 2.4.2
  PPP MPPE Compression module registered
  NET: Registered protocol family 24
  PPTP driver version 0.8.5
  === PPTP init ===
  u32 classifier
  Actions configured
  Netfilter messages via NETLINK v0.30.
  nf_conntrack version 0.5.0 (3990 buckets, 15960 max)
  xt_time: kernel timezone is -0000
  ip_tables: (C) 2000-2006 Netfilter Core Team
  TCP cubic registered
  NET: Registered protocol family 10
  ip6_tables: (C) 2000-2006 Netfilter Core Team
  NET: Registered protocol family 17
  L2TP core driver, V2.0
  PPPoL2TP kernel driver, V2.0
  802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  All bugs added by David S. Miller <davem@redhat.com>
  Registering the dns_resolver key type
  Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
  NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
  Spare area=64 eccbytes 56, ecc bytes located at:
  2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
  Available 7 bytes at (off,len):
  (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
  Scanning device for bad blocks
  Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
  Creating 2 MTD partitions on "brcmnand":
  0x000002000000-0x000008000000 : "brcmnand"
  0x000004000000-0x000008000000 : "jffs2"
  VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
  devtmpfs: mounted
  Freeing init memory: 216K
  emf: module license 'Proprietary' taints kernel.
  Disabling lock debugging due to kernel taint
  et_module_init: passivemode set to 0x0
  et_module_init: txworkq set to 0x0
  et_module_init: et_txq_thresh set to 0x0
  eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
  wl_module_init: passivemode set to 0x0
  wl_module_init: txworkq set to 0x0
  PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
  eth1: Broadcom BCMa8db 802.11 Wireless Controller 6.37.14.86 (r456083)
  eth2: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.86 (r456083)
  JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  usbcore: registered new interface driver usbfs
  usbcore: registered new interface driver hub
  usbcore: registered new device driver usb
  SCSI subsystem initialized
  csw_retry 100
  Initializing USB Mass Storage driver...
  usbcore: registered new interface driver usb-storage
  USB Mass Storage support registered.
  jnl: driver (lke_8.9.0, Apr 9 2014 16:56:06, LBD=ON) loaded at bf599000
  ufsd:: trace mask set to 0000000f
  ufsd: driver (lke_8.9.0 lke_8.9.0_r225078_b43, LBD=ON, delalloc, acl, ioctl, ugm, sd(1), wb, tr) loaded at bf5a6000
  NTFS support included
  Hfs+/HfsJ support included
  optimized: speed
  Build_for__ASUS_PRODUCTS_003_lke_8.9.0_r225078_b43
  
  xhci_hcd 0000:00:0c.0: xHCI Host Controller
  xhci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 1
  xhci_hcd 0000:00:0c.0: irq 112, io mem 0x18023000
  xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
  xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
  usb usb1: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values
  xHCI xhci_add_endpoint called for root hub
  xHCI xhci_check_bandwidth called for root hub
  hub 1-0:1.0: USB hub found
  hub 1-0:1.0: 1 port detected
  [xhci-hub] usb2mode:[0]
  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  ehci_hcd 0000:00:0b.1: EHCI Host Controller
  ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
  ehci_hcd 0000:00:0b.1: irq 111, io mem 0x18021000
  ehci_hcd 0000:00:0b.1: USB 0.0 started, EHCI 1.00
  hub 2-0:1.0: USB hub found
  hub 2-0:1.0: 2 ports detected
  usbcore: registered new interface driver hiddev
  usbcore: registered new interface driver usbhid
  usbhid: USB HID core driver
  usb 2-2: new high speed USB device using ehci_hcd and address 2
  scsi0 : usb-storage 2-2:1.0
  scsi1 : usb-storage 2-2:1.1
  device vlan1 entered promiscuous mode
  device eth0 entered promiscuous mode
  device eth1 entered promiscuous mode
  scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2
  scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
  sd 1:0:0:0: [sda] Attached SCSI removable disk
  device eth2 entered promiscuous mode
  br0: port 3(eth2) entering forwarding state
  br0: port 3(eth2) entering forwarding state
  br0: port 2(eth1) entering forwarding state
  br0: port 2(eth1) entering forwarding state
  br0: port 1(vlan1) entering forwarding state
  br0: port 1(vlan1) entering forwarding state
  ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://code.google.com/p/ipt-account/
  usb 2-2: USB disconnect, address 2
  usbcore: registered new interface driver cdc_acm
  cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  USB Serial support registered for GSM modem (1-port)
  usbcore: registered new interface driver option
  option: v0.7.2:USB Driver for GSM modems
  USB Serial support registered for Sierra USB modem
  usbcore: registered new interface driver sierra
  sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems
  usbcore: deregistering interface driver sierra
  USB Serial deregistering driver Sierra USB modem
  usbcore: deregistering interface driver option
  USB Serial deregistering driver GSM modem (1-port)
  usbcore: deregistering interface driver usbserial_generic
  USB Serial deregistering driver generic
  usbcore: deregistering interface driver usbserial
  usbcore: deregistering interface driver cdc_acm
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  usbcore: deregistering interface driver usbserial_generic
  USB Serial deregistering driver generic
  usbcore: deregistering interface driver usbserial
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  usb 2-2: new high speed USB device using ehci_hcd and address 3
  scsi2 : usb-storage 2-2:1.5
  scsi3 : usb-storage 2-2:1.6
  scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
  scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2
  sd 3:0:0:0: [sda] Attached SCSI removable disk
  
  gro disabled
  
  gro enabled with interval 2
  
  gro enabled with interval 2
  usbcore: registered new interface driver cdc_acm
  cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
  USB Serial support registered for GSM modem (1-port)
  usbcore: registered new interface driver option
  option: v0.7.2:USB Driver for GSM modems
  USB Serial support registered for Sierra USB modem
  usbcore: registered new interface driver sierra
  sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems
  usbcore: deregistering interface driver sierra
  USB Serial deregistering driver Sierra USB modem
  usbcore: deregistering interface driver option
  USB Serial deregistering driver GSM modem (1-port)
  usbcore: deregistering interface driver usbserial_generic
  USB Serial deregistering driver generic
  usbcore: deregistering interface driver usbserial
  usbcore: deregistering interface driver cdc_acm
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  usbcore: deregistering interface driver usbserial_generic
  USB Serial deregistering driver generic
  usbcore: deregistering interface driver usbserial
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  usbcore: deregistering interface driver usbserial_generic
  USB Serial deregistering driver generic
  usbcore: deregistering interface driver usbserial
  usbcore: registered new interface driver usbserial
  USB Serial support registered for generic
  usbserial_generic 2-2:1.0: generic converter detected
  usb 2-2: generic converter now attached to ttyUSB0
  usbserial_generic 2-2:1.1: Generic device with no bulk out, not allowed.
  usbserial_generic: probe of 2-2:1.1 failed with error -5
  usbserial_generic 2-2:1.2: generic converter detected
  usb 2-2: generic converter now attached to ttyUSB1
  usbserial_generic 2-2:1.3: generic converter detected
  usb 2-2: generic converter now attached to ttyUSB2
  usbserial_generic 2-2:1.4: generic converter detected
  usb 2-2: generic converter now attached to ttyUSB3
  usbcore: registered new interface driver usbserial_generic
  usbserial: USB Serial Driver core
  -
  -----------------------------------------------------------------------
  
  Bus 001 Device 001: ID 1d6b:0003
  Bus 002 Device 001: ID 1d6b:0002
  Bus 002 Device 003: ID 12d1:1506

  Sajnálom hogy ilyen hosszu és kissé beszemeteli a topikot, de ha majd megoldodik a gond, akkor admin nyugodtan törölje.

  https://logout.hu/tema/re_qiku_360_n4s_a_biztonsagban_rejlo_energia/friss.html

Új hozzászólás Aktív témák