Új hozzászólás Aktív témák

• #21874 doberman senior tag vargalex #21870

  Új Válasz 2012-01-31 15:30:55 #21874

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  doberman

  senior tag

  válasz vargalex #21870 üzenetére

  ajaj.. hosszú lesz:

  [ 0.000000] Linux version 2.6.39.4 (gavarga@gavarga-laptop) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #27 Wed Jan 4 15:44:14 CET 2012
  [ 0.000000] prom: fw_arg0=00000001, fw_arg1=80a01920, fw_arg2=00000000, fw_arg3=00000000
  [ 0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=ffffffff
  [ 0.000000] bootconsole [early0] enabled
  [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
  [ 0.000000] SoC: Atheros AR9132 rev 2
  [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
  [ 0.000000] Determined physical RAM map:
  [ 0.000000] memory: 02000000 @ 00000000 (usable)
  [ 0.000000] Initrd not found or empty - disabling initrd
  [ 0.000000] Zone PFN ranges:
  [ 0.000000] Normal 0x00000000 -> 0x00002000
  [ 0.000000] Movable zone start PFN for each node
  [ 0.000000] early_node_map[1] active PFN ranges
  [ 0.000000] 0: 0x00000000 -> 0x00002000
  [ 0.000000] On node 0 totalpages: 8192
  [ 0.000000] free_area_init_node: node 0, pgdat 802cbcb0, node_mem_map 81000000
  [ 0.000000] Normal zone: 64 pages used for memmap
  [ 0.000000] Normal zone: 0 pages reserved
  [ 0.000000] Normal zone: 8128 pages, LIFO batch:0
  [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  [ 0.000000] pcpu-alloc: [0] 0
  [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  [ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
  [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
  [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  [ 0.000000] Writing ErrCtl register=00000000
  [ 0.000000] Readback ErrCtl register=00000000
  [ 0.000000] Memory: 29280k/32768k available (2084k kernel code, 3488k reserved, 396k data, 188k init, 0k highmem)
  [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  [ 0.000000] NR_IRQS:80
  [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
  [ 0.080000] pid_max: default: 32768 minimum: 301
  [ 0.080000] Mount-cache hash table entries: 512
  [ 0.090000] NET: Registered protocol family 16
  [ 0.090000] MIPS: machine is TP-LINK TL-WR1043ND
  [ 0.350000] bio: create slab <bio-0> at 0
  [ 0.360000] Switching to clocksource MIPS
  [ 0.360000] NET: Registered protocol family 2
  [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  [ 0.370000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  [ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  [ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
  [ 0.390000] TCP reno registered
  [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  [ 0.400000] NET: Registered protocol family 1
  [ 0.410000] PCI: CLS 0 bytes, default 32
  [ 0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  [ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  [ 0.440000] msgmni has been set to 57
  [ 0.440000] io scheduler noop registered
  [ 0.450000] io scheduler deadline registered (default)
  [ 0.450000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  [ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  [ 0.490000] console [ttyS0] enabled, bootconsole disabled
  [ 0.500000] Atheros AR71xx SPI Controller driver version 0.2.4
  [ 0.510000] m25p80 spi0.0: found s25sl064a, expected m25p80
  [ 0.510000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
  [ 0.520000] 5 tp-link partitions found on MTD device spi0.0
  [ 0.520000] Creating 5 MTD partitions on "spi0.0":
  [ 0.530000] 0x000000000000-0x000000020000 : "u-boot"
  [ 0.540000] 0x000000020000-0x000000100000 : "kernel"
  [ 0.540000] 0x000000100000-0x0000007f0000 : "rootfs"
  [ 0.550000] mtd: partition "rootfs" set to be root filesystem
  [ 0.560000] mtd: partition "rootfs_data" created automatically, ofs=6F0000, len=100000
  [ 0.560000] 0x0000006f0000-0x0000007f0000 : "rootfs_data"
  [ 0.570000] 0x0000007f0000-0x000000800000 : "art"
  [ 0.580000] 0x000000020000-0x0000007f0000 : "firmware"
  [ 0.590000] Realtek RTL8366RB ethernet switch driver version 0.2.3
  [ 0.590000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
  [ 0.600000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
  [ 0.660000] rtl8366rb: probed
  [ 0.670000] eth0: Atheros AG71xx at 0xb9000000, irq 4
  [ 0.970000] eth0: using fixed link parameters
  [ 0.970000] Atheros AR71xx hardware watchdog driver version 0.1.0
  [ 0.980000] ar71xx-wdt: timeout=15 secs (max=21)
  [ 0.980000] TCP westwood registered
  [ 0.990000] NET: Registered protocol family 17
  [ 0.990000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  [ 1.000000] All bugs added by David S. Miller <davem@redhat.com>
  [ 1.010000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  [ 1.020000] Freeing unused kernel memory: 188k freed
  [ 3.310000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
  [ 3.400000] Button Hotplug driver version 0.4.1
  [ 3.430000] ar71xx: pll_reg 0xb8050014: 0x1a000000
  [ 3.430000] eth0: link up (1000Mbps/Full duplex)
  [ 3.580000] Registered led device: tp-link:green:usb
  [ 3.580000] Registered led device: tp-link:green:system
  [ 3.580000] Registered led device: tp-link:green:qss
  [ 3.580000] Registered led device: tp-link:green:wlan
  [ 6.920000] JFFS2 notice: (416) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 23 of xref (0 dead, 6 orphan) found.
  [ 7.610000] SCSI subsystem initialized
  [ 7.870000] usbcore: registered new interface driver usbfs
  [ 7.870000] usbcore: registered new interface driver hub
  [ 7.880000] usbcore: registered new device driver usb
  [ 8.650000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  [ 8.660000] ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
  [ 8.660000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
  [ 8.700000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
  [ 8.720000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
  [ 8.720000] hub 1-0:1.0: USB hub found
  [ 8.730000] hub 1-0:1.0: 1 port detected
  [ 8.870000] Initializing USB Mass Storage driver...
  [ 8.870000] usbcore: registered new interface driver usb-storage
  [ 8.880000] USB Mass Storage support registered.
  [ 8.900000] usbcore: registered new interface driver ums-alauda
  [ 8.920000] usbcore: registered new interface driver ums-cypress
  [ 8.950000] usbcore: registered new interface driver ums-datafab
  [ 8.970000] usbcore: registered new interface driver ums-freecom
  [ 8.990000] usbcore: registered new interface driver ums-isd200
  [ 9.010000] usbcore: registered new interface driver ums-jumpshot
  [ 9.040000] usbcore: registered new interface driver ums-karma
  [ 9.060000] usbcore: registered new interface driver ums-sddr09
  [ 9.080000] usbcore: registered new interface driver ums-sddr55
  [ 9.100000] usb 1-1: new high speed USB device number 2 using ar71xx-ehci
  [ 9.120000] usbcore: registered new interface driver ums-usbat
  [ 9.250000] scsi0 : usb-storage 1-1:1.0
  [ 10.260000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G3 PMAP PQ: 0 ANSI: 0 CCS
  [ 10.270000] sd 0:0:0:0: [sda] 15215808 512-byte logical blocks: (7.79 GB/7.25 GiB)
  [ 10.280000] sd 0:0:0:0: [sda] Write Protect is off
  [ 10.280000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
  [ 10.280000] sd 0:0:0:0: [sda] Assuming drive cache: write through
  [ 10.290000] sd 0:0:0:0: [sda] Assuming drive cache: write through
  [ 10.300000] sda: sda1 sda2 sda3
  [ 10.310000] sd 0:0:0:0: [sda] Assuming drive cache: write through
  [ 10.310000] sd 0:0:0:0: [sda] Attached SCSI removable disk
  [ 29.600000] EXT4-fs (sda2): recovery complete
  [ 29.610000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
  [ 29.810000] eth0: link down
  [ 30.400000] Compat-wireless backport release: compat-wireless-2011-11-29
  [ 30.410000] Backport based on wireless-testing.git master-2011-12-01
  [ 30.540000] cfg80211: Calling CRDA to update world regulatory domain
  [ 30.650000] cfg80211: World regulatory domain updated:
  [ 30.650000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  [ 30.660000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 30.670000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  [ 30.680000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  [ 30.680000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 30.690000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 31.470000] ath: EEPROM regdomain: 0x0
  [ 31.470000] ath: EEPROM indicates default country code should be used
  [ 31.470000] ath: doing EEPROM country->regdmn map search
  [ 31.470000] ath: country maps to regdmn code: 0x3a
  [ 31.470000] ath: Country alpha2 being used: US
  [ 31.470000] ath: Regpair used: 0x3a
  [ 31.480000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  [ 31.480000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
  [ 31.490000] cfg80211: Calling CRDA for country: US
  [ 31.540000] cfg80211: Regulatory domain changed to country: US
  [ 31.540000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  [ 31.550000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  [ 31.560000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  [ 31.570000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 31.580000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 31.580000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  [ 31.590000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  [ 32.250000] PPP generic driver version 2.4.2
  [ 32.320000] tun: Universal TUN/TAP device driver, 1.6
  [ 32.330000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  [ 32.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
  [ 32.640000] NET: Registered protocol family 24
  [ 32.880000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
  [ 33.360000] xt_time: kernel timezone is -0000
  [ 33.650000] usbcore: registered new interface driver usblp
  [ 34.030000] fuse init (API version 7.16)
  [ 34.830000] ar71xx: pll_reg 0xb8050014: 0x1a000000
  [ 35.130000] eth0: link up (1000Mbps/Full duplex)
  [ 35.670000] device eth0.1 entered promiscuous mode
  [ 35.670000] device eth0 entered promiscuous mode
  [ 35.730000] br-lan: port 1(eth0.1) entering forwarding state
  [ 35.740000] br-lan: port 1(eth0.1) entering forwarding state
  [ 37.320000] Adding 127320k swap on /dev/sda1. Priority:-1 extents:1 across:127320k
  [ 37.700000] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
  [ 40.420000] device wlan0 entered promiscuous mode
  [ 40.420000] br-lan: port 2(wlan0) entering forwarding state
  [ 40.430000] br-lan: port 2(wlan0) entering forwarding state
  [ 44.190000] device wlan0 left promiscuous mode
  [ 44.190000] br-lan: port 2(wlan0) entering forwarding state
  [ 44.320000] device wlan0 entered promiscuous mode
  [ 44.320000] br-lan: port 2(wlan0) entering forwarding state
  [ 44.330000] br-lan: port 2(wlan0) entering forwarding state
  [ 55.790000] ar71xx-wdt: enabling watchdog timer
  [ 56.390000] device tap0 entered promiscuous mode
  [ 56.400000] br-lan: port 3(tap0) entering forwarding state
  [ 56.400000] br-lan: port 3(tap0) entering forwarding state

  elnézést mindenkitől... hosszú lett.

  z

  8lnu

Új hozzászólás Aktív témák